Visit by appointment · Nationwide delivery · Free delivery on orders over £75 · Free RFD transfers on all new firearms. How it works ›
Buying guide

Moderator threads, and how to be sure.

Thread pitch is where most moderator orders go wrong, and it is not always what the rifle maker lists. There is no reliable shortcut from the name of your rifle to the thread on its muzzle, so this guide does the opposite: it shows you the handful of threads you are likely to meet, the three pairs that get mistaken for each other, and how to measure yours in a minute with a pair of callipers.

Why this is the step that goes wrong

A moderator either threads onto your muzzle or it does not. There is no partly. So it is worth a minute getting this right, because the two failure modes are both bad: a thread that will not start at all, or worse, one that starts, feels nearly right, and cross threads. The second ruins a muzzle.

Three things make it harder than it should be.

  • Factory threads vary by market and by variant. The same model name can leave the factory with a different thread for Europe than for America, and can change between production runs. A rifle is not a thread.
  • A lot of UK rifles were threaded after they were sold. If a gunsmith cut the thread, it is whatever that customer's moderator needed at the time, which tells you nothing about what the maker fits.
  • Most published thread charts are American. They are accurate for American rifles and misleading for European ones, and almost every rifle in a British gun cabinet is one or the other.

Which is why we will not publish a table that claims to tell you the thread on your rifle from its name. We would be wrong often enough to send people the wrong moderator. What follows is the thread itself, which you can check in your own hands.

The threads you will meet

Nearly every sporting rifle in the UK carries one of seven threads. The first four are metric and come mostly from European factories; the last three are the American inch series, written in this guide as diameter and threads per inch.

ThreadDiameterPitchThreads in 10 mmWhere you tend to meet it
M13x113.00 mm1.00 mm10Less common. Some pistols and older military patterns.
M14x114.00 mm1.00 mm10Very common on European hunting rifles.
M15x115.00 mm1.00 mm10Some German rifles.
M18x118.00 mm1.00 mm10European rifles with heavy or bull barrels.
1/2 in x 2012.70 mm1.27 mmabout 7.9Older European rimfires in .22 LR.
1/2 in x 2812.70 mm0.91 mmabout 11American rifles in .223, .22 LR and 9 mm.
5/8 in x 2415.88 mm1.06 mmabout 9.4American .30 calibre rifles, the Uintah UPR-10 among them.

Diameter here is the nominal major diameter, which is what callipers across the crests of the thread will read, give or take a couple of hundredths. The threads-in-10-mm column is the one to use if you do not own a pitch gauge, and it is worked out from the pitch rather than measured, so it is exact.

The inch threads are usually written with a class suffix, so 1/2 in x 20 appears as 1/2x20 UNF and the other two as 1/2x28 UNEF and 5/8x24 UNEF. The suffix describes the thread series, not a different size, so you can ignore it when matching.

Left hand threads exist. They are uncommon on sporting rifles but you do meet them, and a left hand thread will not accept a right hand moderator whatever the size says. If yours tightens anticlockwise, say so when you order.

The three pairs that get confused

These are the mistakes worth knowing by heart, because each pair looks identical at arm's length and only one of the two will fit.

1/2x20 against 1/2x28

Same diameter, 12.70 mm, every time. The only difference is the pitch, and that is the difference between a moderator that spins on and one that strips a thread. 1/2x20 gives you about 7.9 threads in 10 mm and 1/2x28 about 11. If you take nothing else from this guide, take this: callipers alone cannot tell these apart. You have to count.

1/2x20 against M14x1

1.3 mm apart in diameter and both around a millimetre of pitch, which is close enough that people buy the wrong one on sight. Callipers settle it instantly: 12.70 mm against 14.00 mm.

M15x1 against 5/8x24

The closest pair of the three, 15.00 mm against 15.88 mm, less than a millimetre apart. The pitch differs too, 1.00 mm against 1.06 mm, but not by enough to feel. Measure the diameter.

Measuring yours, in a minute

You need a pair of callipers. A thread pitch gauge makes it quicker but is not essential.

  • Diameter. Measure across the crests of the thread, not across the thread protector. Round to the nearest tenth of a millimetre and read it off the table above. If you get 12.7, you have an inch thread and still need the pitch. If you get 14, 15 or 18, you are almost certainly metric and nearly done.
  • Pitch, with a gauge. Try leaves until one sits in the thread with no light under it. Guesswork at this stage is what cross threads muzzles.
  • Pitch, without a gauge. Mark 10 mm along the thread and count the crests in it. Ten means a 1 mm metric pitch. Eight means 1/2x20. Eleven means 1/2x28. Nine and a bit means 5/8x24, and you should have measured 15.88 mm across the crests to confirm it.
  • The protector is a clue, not evidence. A thread protector that came with the rifle will match the rifle, but protectors get swapped and lost. Measure the barrel.

If the rifle is in front of us anyway, bring it. We will gauge it while you wait, and that is the end of the question for the life of the barrel.

Your rifle's nationality is a clue, not an answer

As a rule of thumb, a European sporting rifle is more likely to be metric and an American one more likely to be inch. That is useful for narrowing it down and useless as a conclusion. Plenty of European rifles leave the factory in 5/8x24 because that is what the American market wanted that year, and plenty of American rifles sold here were rethreaded metric by a British gunsmith because that is what the owner's moderator was.

One thread we can state outright, because we distribute the rifle: the Uintah Precision UPR-10 is threaded 5/8x24. On the UPR-15 it depends on which calibre you build, so ask us and we will confirm it against the build.

Adapters, and when not to use one

A thread adapter turns one thread into another, and the UK trade is full of them: M14x1 to 1/2x20, M15x1 to 5/8x24, left hand to right hand, and so on. They are a legitimate answer in two situations: a moderator you already own and want to keep across a new rifle, and a thread so unusual that nothing is made for it.

They are the wrong answer in two others.

  • On a new purchase. If you are buying the moderator anyway, buy it in your thread. An adapter adds a joint, a little length and a little weight at the worst possible place, which is the far end of a lever.
  • Where concentricity matters. Every extra interface is another chance for the moderator to sit slightly off the bore axis. On a rifle you expect to shoot sub-MOA with, that is a poor trade for saving the cost of the right thread.

If a barrel needs rethreading rather than adapting, that is a gunsmithing job and we can talk it through. It is often the cheaper answer over the life of the rifle.

Tell us three things and we will confirm it

Our moderator listings do not ask you to pick a thread at checkout, and that is deliberate: we would rather confirm the fit than let you guess it. Send us these three and we will have it right before anything is paid for.

  • The rifle, make and model.
  • The calibre.
  • The thread, if you know it, or your two measurements if you do not.

Then the choice is the interesting part rather than the risky part. Choosing a moderator covers over barrel against front mount, calibre ratings and care. The moderators we stock run from the Aimsport Triton range, which we distribute in the UK, through HQS, Wildcat, Svemko, ASE Utra and Silent Steel.

On the certificate side, our guide to the 2026 law is the page to read, and it is the one we keep up to date.

Common questions

How do I find out what thread my rifle has?

Measure it. Callipers across the crests of the thread give you the diameter: 12.70 mm means an inch thread, 14.00, 15.00 or 18.00 mm means metric. Then get the pitch, either with a thread pitch gauge or by counting the crests along 10 mm. Ten crests in 10 mm is a 1 mm metric pitch, about eight is 1/2x20, about eleven is 1/2x28 and about nine and a half is 5/8x24. Do not work from the rifle's model name, because factory threads vary by market and variant and many UK rifles were threaded after sale.

Is there a standard thread for a Tikka, a Howa or a CZ?

Not one you can rely on. Factory threads change between markets and between production runs, and a large share of rifles in British cabinets were threaded by a gunsmith after purchase, in whatever that owner's moderator needed. Measure the barrel rather than trusting a chart against the model name.

What is the difference between 1/2x20 and 1/2x28?

Only the pitch. Both are 12.70 mm across the crests, so callipers cannot tell them apart. 1/2x20 has 20 threads to the inch, a 1.27 mm pitch, about 7.9 crests in 10 mm. 1/2x28 has 28 threads to the inch, a 0.91 mm pitch, about 11 crests in 10 mm. This is the pair that cross threads muzzles, so count before you order.

Can I use a thread adapter instead?

Sometimes. An adapter is a reasonable answer for a moderator you already own and want to carry onto another rifle, or for a thread nothing is made for. It is the wrong answer on a new purchase, where you should simply buy the moderator in your own thread, because an adapter adds a joint, length and weight at the muzzle and one more chance for the moderator to sit off the bore axis.

What thread is the Uintah Precision UPR-10?

5/8x24. On the UPR-15 it depends which calibre the rifle is built in, so ask and we will confirm it against your build.

What if I measure it and still am not sure?

Bring the rifle in and we will gauge it while you wait, or send us the rifle, the calibre and your two measurements and we will work it out before anything is paid for.

Last reviewed 21 November 2026. Spotted something out of date? Tell us and we will fix it.

WhatsApp us